Publications

Showing 1976 - 2000 of 2013 results
Building Commission
Form – application
14 May 2014
Building Commission
Form – application
14 May 2014
Electric drills vary in noise output according to type. Hammer drills produce the highest noise levels because of their impact function. The quality and method of construction of the drill also...
WorkSafe
Fact sheet
14 May 2014
Angle grinders are used extensively in the metalworking and panel beating areas and can be used for wood carving when equipped with an "Arbortech" woodcarving disc. Other accessories such as...
WorkSafe
Fact sheet
14 May 2014
Hand held belt sanders range in noise level from 92 to 103 dB(A). The noise levels are directly affected by the quality and condition of the tool. The free running noise level of a belt sander is...
WorkSafe
Fact sheet
14 May 2014
Orbital sanders range in noise level quite dramatically, the quietest currently being the Festo and ELU brands (80-82 dB(A)). The noise levels are directly affected by the quality and condition of...
WorkSafe
Fact sheet
14 May 2014
This educational article has been developed to assist in the identification of occupational safety and health (OSH) hazards. The hazard identification tools were developed following interviews with...
WorkSafe
Fact sheet
13 May 2014
A report into the wild fire that occurred at Location 745 Bates Road, Dalyup, about 20 km west of Esperance, on Thursday 2 December 2005.
EnergySafety
Reports
12 May 2014
This application form is used to apply for a ground geophysical survey equipment permit.
EnergySafety
Form – application
05 May 2014
This application form is used to apply for a mobile mining permit.
EnergySafety
Form – application
05 May 2014
This application form is used to restore a name to the Electrical Licensing Register.
EnergySafety
Form – application
05 May 2014
This form is used to notify Energy Safety of a change of name to an electrical worker's licence, permit, or certificate of registration and obtain an updated licence card.
EnergySafety
Form – application
05 May 2014
Notice of termination by park operator or tenant agreement frustrated Form 2011
Consumer Protection
Form – notification
04 May 2014
Residential Parks condition report site only agreement
Consumer Protection
Reports
04 May 2014
This is what an electrical safety certificate looks like. You should receive one from your electrical contractor within 28 days of the electrical work (other than repairs) being done.
EnergySafety
Information
02 May 2014
This advisory letter is issued by the electrical contractor or electrician to the owner or occupier to inform them that unenclosed joints were found and remedial work is to be carried out.
EnergySafety
Advisory note
02 May 2014
This publication will assist event organisers, venue organisers, asset managers and catering vendors to comply with the safety requirements for the use of gas appliances in public venues.
EnergySafety
Brochure
30 Apr 2014
A guide for the safe operation of an LP gas powered vehicle. Auto LP Gas safety Just like other forms of energy, LP gas (liquefied petroleum gas) is safe when treated properly. A correctly installed...
EnergySafety
Brochure
30 Apr 2014
This publication provides information on how to obtain approval to sell, hire or use Type A (domestic or commercial) gas appliances in Western Australia.
EnergySafety
Brochure
30 Apr 2014
An audit has been conducted on Western Power's Service Connect Scheme. The report includes the audit conclusions and recommendations.
EnergySafety
Reports
30 Apr 2014
A wild fire occurred at Location 1434, South Coast Highway, about 42 km west of Esperance, on 15 December 2004. Energy Safety carried out an investigation into the cause of the fire and determined...
EnergySafety
Reports
30 Apr 2014
A wild fire occurred at Lot 2 Location 1039, Moonup Road, about 40 km west of Esperance, on Tuesday 14 December 2004. Energy Safety carried out an investigation into the cause of the fire and...
EnergySafety
Reports
30 Apr 2014
A wild fire occurred at Location 1482 South Coast Highway, about 72 km west of Esperance, on Friday 10 December 2004. Energy Safety carried out an investigation into the cause of the fire and...
EnergySafety
Reports
30 Apr 2014
Energy Safety carried out an investigation into the fire and could not determine the cause. The fire originated in the area of a network operator's power pole. However, there was no evidence of...
EnergySafety
Reports
29 Apr 2014
Energy Safety carried out an investigation into the cause of the fire in Dunsborough. It was determined that the cause of the fire was a leakage current due to dust or salt spray on the insulators,...
EnergySafety
Reports
29 Apr 2014

Pages